Rock pole sliding floating fishing group, floating should be so adjusted!

The rocky pole slide drift fishing group has been introduced many times in the previous content, but it mainly introduces the matching points of the fishing group, and less introduces the drift adjustment. In summer, fishing is mostly deep and far away. More and more fishing friends have discovered the beauty of this more practical and less equipped fishing method. Can catch near, can also catch far, can catch bottom can also catch floating, one equipment catches the world, is very easy to use. Therefore, I would like to introduce the drift adjustment skills of the slide drift fishing team, hoping to help all fishing friends.

I. Key Points of Fishing Group Matching

It is still necessary to briefly introduce the matching points of the lower fishing groups, and the accessories on these fishing groups need to be used in the drift adjustment. In a simple description, the sliding floating fishing group is a fishing group in which the float can slide in an interval. The purpose is to use a long line for the short rod. When the rod is thrown, the float is pulled to a position close to the lead pendant. After the long-range throw is in place, the fishing group sinks, and the float will slide in this interval to realize the purpose of fishing bottom or floating. To achieve this goal, one space bean is needed, one cotton knot is needed to control the downward movement of the float, and one cotton knot is needed to control the upward movement of the float. The float can move between the space bean and the cotton knot. The cotton knot is too small to block the floating seat, so there needs to be a stop bean between them, which can block the floating seat, but it is just blocked by the cotton knot, and the stop bean can slide on the fishing line, thus forming a slip drift. In order to achieve the purpose of fixed point, it is necessary to add a cotton knot. It is believed that this cotton knot will not be tied until the fishing point is determined.

2. Bleaching adjustment method

1. Fishing and floating

In fact, the drift adjustment method is not difficult, and there is no essential difference with the conventional platform fishing drift adjustment method, especially when fishing float. Two methods can be adopted, i.e. Bait with bait or empty hook, and the bait for long-range feeding is basically bait such as corn kernels and granular rubber bands. Noodle bait is easy to fall off, so it is basically not used. The change of bait weight is small, so it is recommended to adjust drift with bait. The method is to adjust the drift nearby now, casually determine a half-water depth, and hang double baits to trim the lead skin just like the fishing rod adjustment, until the float is exposed to the required number of mesh.

It is suggested that the fishing eye should be higher and the floating will be clearer. Then start long-range shooting, adjust the position of cotton knot before long-range shooting, control the sliding interval of float, and realize the change of fishing water depth. Find punctuation marks on the other side, throw the rod in one direction at a time, determine the fishing point and water depth, tie a cotton thread to the fishing line, which can be at the slightly located position of the rod, or the line near the wheel. Then every time it is a pay-off pole, every time it takes up the thread to the place where the cotton thread knot is tied, thus realizing the purpose of fixed-point fishing and floating.

2. Fishing Bottom

In fact, the bottom of the fishing is the same as that of the conventional platform fishing, but no matter the bottom of the fishing or the floating of the fishing, it is impossible to be as fine and accurate as the hand rod, and it is almost enough to pay attention to it. It is impossible to choose the appropriate semi-water depth to adjust the drift at the bottom of fishing, so the method is still semi-water drift in shallow water area, and the depth does not matter. It can be adjusted to level water or exposed to 1 mesh. Then hang the double bait and throw it to the fishing point at a long distance. At the same time, adjust the position of the first cotton knot repeatedly until the float is above the water for 3 or 4 mesh and then stop. That will do. Frankly speaking, it is the method of directly adjusting the drift without looking for the bottom. As a result, the water depth can only be tested repeatedly when looking for the bottom accurately.

The long-range slide and drift fishing team itself can’t pay attention to accuracy. First of all, the float itself is lead-heavy and blunt, and the tail of the float often changes in thickness or is very thick, so it is almost enough. After all, it is summer to catch big fish from a long distance, and the big fish will not be unable to float. If you like, please pay attention to it and give it a compliment. Update it on time every day. Thank you, fishing friends!