Skills of adjusting drift: Illustrate the state of different fishing line groups in water with bait and adjusting drift, which is very practical.

This paper introduces the drift adjustment with bait. The drift adjustment with bait is more scientific and accurate because the bait weight is fully considered. Of course, there are also disadvantages, that is, when the bait is too heavy, it is not suitable to use bait to adjust the drift. Conventional bait pulling and baiting can be used. I am not very good at drawing, so I drew a little picture casually, but it is almost the same to be able to express the meaning. From the perspective of drift adjustment steps, bait weight and fishing purpose, let’s talk about the magic drift adjustment with bait, hoping to help all fishing friends.

First, find the bottom

Finding the bottom is always the first step in the drift adjustment. The purpose is to determine the water depth and the semi-water depth at the same time. The lead skin is wrapped with enough lead skin to pull all the floats into the water, and then adjust the position of the floats. It is advisable to expose 1 or 2 mesh of the floats. In this way, even if the rough bottom finding is completed, the approximate water depth can be determined. Then float down a distance that exceeds the length of the sub-line, usually 2 times the length of the sub-line. It is more accurate to lower the float at this depth. It should be noted that the more deep water is fished, the more attention should be paid to the influence of semi-water depth on drift adjustment. Remember.

2. Bleaching with Bait

Once the semi-water depth has been determined, the official drift adjustment will begin. The characteristic of bait drift adjustment is that bait weight is involved in the process of bait drift adjustment and fishing adjustment, so it is more scientific and practical, and there will be no embarrassing fishing purpose without considering bait weight. Hang up the double bait and trim the lead skin to the desired number of mesh. The number of semi-water mesh with double bait is often not much different from the final mesh, so if you want to catch a high mesh, you can raise the mesh with bait here, and if you want to catch a low mesh, you can naturally raise the mesh with bait. For example, the following figure has been adjusted by 2 mesh.

Three, determine the empty hook adjustment purpose or hanging single bait adjustment purpose

At this stage, the bait adjustment and drift is basically completed. At this time, it is necessary to remove the double bait and see the number of empty hooks, so that the bait weight can be inferred. For example, the bait is adjusted to 2 mesh, and the double bait is 6 mesh after removing the double bait, and the weight of the double bait is 4 mesh. You can also remove one bait and only hang a single bait to see the number of mesh at this time. According to the above assumptions, the single bait must be 6-2=4 mesh, as shown in the figure below. The weight of the double bait has been determined, and the weight of the single bait has been adjusted accordingly. Then the double bait is hung and the bottom is found.

Four, find the bottom

According to the characteristics of floating with double baits, the floating with semi-water hanging double baits is the most spiritual fishing eye at the bottom and also the floating fishing eye. When looking for the bottom, as long as the fishing mesh is slightly larger than 2 mesh, the bait will definitely start to touch the bottom, as shown in the figure below.

When the fishing mesh is between the double bait and the single bait, it is a state in which the bait is lowered to the bottom and the bait is not lowered to the bottom. According to the above assumption, the fishing order is between 2 and 4 orders, and the bait does not touch the bottom. When the fishing eye is equal to the adjusting eye of the single bait, the upper bait starts to touch the bottom. See the following figure for details:

When the fishing mesh starts to be larger than 4 mesh, the lying state of the upper bait becomes more and more serious. If the fishing mesh continues to be increased, the double bait will lie on the bottom and the twin lines will all bend. How many eyes did the lead pendant reach before it began to lie on the bottom? This requires knowing the weight of the double hook. The weight of the double hook is not weighed in front, so this is not known. According to the formula, fishing mesh = empty hook adjustment mesh + double hook weight, this is the state of no hook adjustment drift, is the state of double hook lying on the bottom all the time. It is somewhat similar to the following figure. When the fishing mesh is larger than the weight of the empty hook adjustment mesh + double hook, the lead pendant starts to touch the bottom.

The above is the detailed steps of bait drift adjustment and the general state of fishing groups at the bottom of the water due to different fishing eyes. The reason why bait drift adjustment is scientific is that the state of double bait at the bottom can be inferred from the relationship between bait weight and fishing purpose adjustment. If you like, please pay attention to it and give it a compliment. Update it on time every day. Thank you, fishing friends!